Channellock® 318 E SERIES™ XLT™ High Leverage Long Nose Plier, Cross Hatched/Serrated High Carbon Steel Jaw, 2.96 in L x 45/64 in W Jaw, 8 in OAL, 0.13 in W Tip
The Channellock® E SERIES™ line-up features Xtreme Leverage Technology (XLT™) for considerably less force required to cut than traditional high leverage designs. Crosshatch jaws provide maximum grip and the pipe grip design accommodates many shapes. Laser heat-treated cutting edges last longer and easily cut hard and soft wire. The streamlined design is sleeker and lighter for easier handling.
-
BrandChannellock®
-
UPC025582828019
-
Manufacturer Part Number318
-
CountryUSA
-
FinishPolished
-
Tip Width0.13 in
-
ColorBlue
-
TypeHigh Leverage
-
Handle Length2.14 in
-
Handle TypeErgonomic/Plastisol Grip
-
Non-SparkingNo
-
SeriesE SERIES™ XLT™
-
Wire Stripper IncludedNo
-
Cutter IncludedYes
-
Jaw Length2.96 in
-
Jaw MaterialHigh Carbon Steel
-
Jaw Opening1-3/8 in
-
Jaw TypeCross Hatched/Serrated
-
Jaw Width45/64 in
-
Overall Length8 in
- XLT™ Xtreme Leverage Technology means considerably less force required to cut than traditional high leverage
- Sleeker, lighter design, streamlined for easier handling
- Crosshatch pattern on jaws grips work tightly
- Laser heat treated cutting edges last longer
- Only Channellock® uses a knife and anvil style cutting edge to ensure perfect mating and superior cutting edge life
- Channellock® uses high carbon steel for superior performance on the job and specially coated for ultimate rust prevention
- Channellock® Blue® grips for comfort
| Competitor Name | Competitor Part Number |
|---|---|
| Ferguson | CE318 |
-
Alternative Part NumberE318
-
UNSPSC27112134
-
Package DescriptionEACH
-
Standards/ApprovalsASME B107
-
WarrantyLimited Lifetime
-
Catalog
Recently Viewed
Channellock® 318 E SERIES™ XLT™ High Leverage Long Nose Plier, Cross Hatched/Serrated High Carbon Steel Jaw, 2.96 in L x 45/64 in W Jaw, 8 in OAL, 0.13 in W Tip
The Channellock® E SERIES™ line-up features Xtreme Leverage Technology (XLT™) for considerably less force required to cut than traditional high leverage designs. Crosshatch jaws provide maximum grip and the pipe grip design accommodates many shapes. Laser heat-treated cutting edges last longer and easily cut hard and soft wire. The streamlined design is sleeker and lighter for easier handling.
Chicago Pneumatic CP7830H Ratchet Wrench, 1/2 in Drive, 122 N-m Torque, 190 rpm Speed, 21 cfm Air Flow, 90 psi
The CP7830 features a maximum torque up to 90 ft.lbs / 122 Nm allowing quick and easy fastening. The progressive throttle allows users to apply the necessary amount of power safely and effectively. The tool benefits from the patented TriSpring Technology which guarantees anti-slip head design. The grease fitting option on the reverse button allows for easier lubrication. The pneumatic ratchet wrench CP7830 Series is composed of 2 models: 3/8 Inch and 1/2 Inch anvil.
The forged steel jaws of this left-cutting snip are set at a 90-degree angle to the handles to allow easy gripping when cutting sheet metal in tight spaces or overhead. The operator can follow tight circular or square pattern left cuts with either a pushing or pulling motion. A serrated edge on the upper jaw and compound head-to-handle linkage provide powerful, non-slip leverage for cutting up to 24-gauge (0.61 mm) cold rolled steel or 28-gauge (0.38 mm) stainless. Handles feature non-slip, cushion inserts, torsion-spring action and a squeeze-open, side operated latch. Rust-resistant polished forged steel jaws and black oxide finished handle stampings promote long service life.
Drillco 695A148D 6950A Center Cutting Double End Imperial Regular Length Finishing End Mill, 3/4 in Dia Cutter, 1-5/8 in Length of Cut, 4 Flutes, 3/4 in Dia Shank, 5-5/8 in OAL, Uncoated
The greater red hardness of M-42 Cobalt end mills enables these tools to run about 10% faster than conventional HSS end mills. This translates to shorter machining times and permits higher utilization of available machine horsepower.
6.75" LONG THIN NEEDLE NOSE PLIER
Drillco 72A108C 7200 Center Cutting Imperial Regular Length Single End Finishing End Mill, 1/8 in Dia Cutter, 3/8 in Length of Cut, 2 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
