KLEIN TOOLS 630-11/32-INS Insulated 11/32'' Nut Driver Hollow
Individually tested to exceed the IEC 60900 and ASTM F1505 standards, for insulated tools, and clearly marked with the official 1000-volt rating symbol.
Two layers of insulation provide protection against electric shock.
Thick, exceptionally tough, high-dielectric white inner coating is bonded to the tool.
A flame retardant, impact-resistant, bright orange outer coating.
Hollow shafts make it possible to work on stacked circuit boards or other long bolt applications.
Tip-Ident quickly identifies nut driver size.
Cushion-Gripā¢ handles for greater torque and comfort.
Recently Viewed
Individually tested to exceed the IEC 60900 and ASTM F1505 standards, for insulated tools, and clearly marked with the official 1000-volt rating symbol.
Two layers of insulation provide protection against electric shock.
Thick, exceptionally tough, high-dielectric white inner coating is bonded to the tool.
A flame retardant, impact-resistant, bright orange outer coating.
Hollow shafts make it possible to work on stacked circuit boards or other long bolt applications.
Tip-Ident quickly identifies nut driver size.
Cushion-Gripā¢ handles for greater torque and comfort.
1/4" X .170" BLUE POLY TUBE--RL-500'-COIPE0417500B>
BondhusĀ® 10964 Ball End Hex Key, L-Handle Handle, ProtaniumĀ® High Torque Steel, ProGuardā¢
BondhusĀ® 10964 Ball End Hex Key, L-Handle Handle, ProtaniumĀ® High Torque Steel, ProGuardā¢
SealmasterĀ® 700188 NP Series Standard-Duty Pillow Block Ball Bearing Unit, 1-7/16 in Dia Bore, 4-11/16 to 5-5/16 in L Bolt Center-to-Center, 1-7/8 in Base to Bore Centerline, 6-9/16 in OAL x 3-3/4 in OAH
SealmasterĀ® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or SkwezlocĀ® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlexĀ® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
ChannellockĀ® 415 Tongue and Groove Plier, 2 in Nominal, 1.38 in L Nickel Smooth Jaw, Smooth Jaw Surface, 10 in OAL
All the versatility and strength of a Straight Jaw Plier, but with a smooth jaw design to protect surfaces from scratching (PVC pipe, chromes etc.). This plier is built to last with a PermaLockĀ® fastener to eliminate nut and bolt failure and a patented reinforcing edge to minimize stress breakage.
SealmasterĀ® 700174 NP Series Standard-Duty Pillow Block Ball Bearing Unit, 5/8 in Dia Bore, 3-3/8 to 4-1/8 in L Bolt Center-to-Center, 1-3/16 in Base to Bore Centerline, 5 in OAL x 2-7/16 in OAH
SealmasterĀ® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or SkwezlocĀ® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlexĀ® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
