Browning® 1214105 Type 6 Spur Gear With Type H Split Taper® Bushing, 8 Diametral Pitch, 14.5 deg Pressure Angle, 1-1/4 in W Face, 28 Teeth, 3-1/2 in Dia Pitch, 3/8 to 1-1/2 in Dia Bore, Steel
Browning® offers a comprehensive line of off the shelf gears, including spur, miter and bevel as well as change gears. These are available in 20 deg pressure angle from 20 to 4 diametral pitch and 14.5 deg pressure angle from 48 to 3 diametral pitch. They are all designed to increase output, reduce costs and avoid the need for custom specials.
-
BrandBrowning®
-
UPC662289115587
-
Manufacturer Part Number1214105
-
CountryUSA
-
Face Width1-1/4 in
-
Pitch Diameter3-1/2 in
-
MaterialSteel
-
Pressure Angle14.5 deg
-
Gear Ratio1:1
-
TypeType 6
-
Hub Diameter2-1/2 in
-
Hub Projection7/16 in
-
Diametral Pitch8
-
Number of Teeth28
-
Keyway Size1/4 x 1/8, 3/16 x 3/32, 5/16 x 5/32 in
-
Outside Diameter3-3/4 in
-
Bore Diameter3/8 to 1-1/2 in
-
Overall Length1-7/8 in
- Browning® Split-Taper® bushed spur gears are shaft ready and eliminate costly reworking of minimum bore gears
- Browning® bushed gears hold the shaft with clamp fit and eliminate costly reworking on replacement gears
- Less expensive
- Without hardened teeth
- Browning Gears are rated in accordance with AGMA standards
- When you think Special Gears - Think Browning
-
Alternative Part NumberNSS8H28
-
UNSPSC31171707
-
Package DescriptionEACH
-
Standards/ApprovalsAGMA Standard
-
Warranty1 Year
-
Warranty Information
-
Catalog
Recently Viewed
Browning® offers a comprehensive line of off the shelf gears, including spur, miter and bevel as well as change gears. These are available in 20 deg pressure angle from 20 to 4 diametral pitch and 14.5 deg pressure angle from 48 to 3 diametral pitch. They are all designed to increase output, reduce costs and avoid the need for custom specials.
W-21 Lock Washer - 4.1920 in ID, 5.7030 in OD, 5.0000 in Face Dia., Steel Material
aterial
Steel
Number Of Tangs
19
Product Type
Bearing Lock Washers
BBI 898440 Wood Screw, #12, 1-1/2 in OAL, Flat Head, Carbon Steel, Phillips® Drive, Zinc CR+3
BBI 898440 Wood Screw, #12, 1-1/2 in OAL, Flat Head, Carbon Steel, Phillips® Drive, Zinc CR+3
6-MM X 1.00X55-MM HEX HEAD CAPSCREW-MET93106055 >
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
Selkirk® by Duravent LockTab® 104018 RV Series Type B Small Diameter Double Wall Round Gas Vent Pipe, Steel, 4 in Dia x 18 in L, Galvanized, Domestic
Our non-positional lock system on the Selkirk® by Duravent RV Gas Vent is the best lock system on the market today. The incorporation of the LockTab® feature simply improves our lock system by adding flexibility and meeting market needs.
