Browning 60-TOOTH 20-PITCH CHANGE GEARS BRW N-CG-20-60
Browning® offers a comprehensive line of off the shelf gears, including spur, miter and bevel as well as change gears. These are available in 20 deg pressure angle from 20 to 4 diametral pitch and 14.5 deg pressure angle from 48 to 3 diametral pitch. They are all designed to increase output, reduce costs and avoid the need for custom specials.
-
BrandBrowning®
-
UPC662289168330
-
Manufacturer Part Number1222017
-
CountryUSA
-
Face Width3/8 in
-
Pitch Diameter3 in
-
MaterialSteel
-
Pressure Angle14.5 deg
-
TypeMinimum Plain Bore Type C1
-
Diametral Pitch20
-
Number of Teeth60
-
Outside Diameter3.1 in
-
Bore Diameter5/8 in
-
Overall Length3/8 in
- Are stocked with finished bore and two keyways
- For use with stock change gear bushings
- Used for easy ratio changes
- Can weld on a steel hub to create a spur gear
- Can drill and tap for bolt on applications
- Can weld on steel hub for use with Browning® split taper bushing
- Browning Change Gears, change gear bushing sold separately
- When you think Special Gears - Think Browning
-
Alternative Part NumberNCG2060
-
UNSPSC31171700
-
Package DescriptionEACH
-
Standards/ApprovalsAGMA Standard
-
Warranty1 Year
-
Warranty Information
-
Catalog
Recently Viewed
Browning® offers a comprehensive line of off the shelf gears, including spur, miter and bevel as well as change gears. These are available in 20 deg pressure angle from 20 to 4 diametral pitch and 14.5 deg pressure angle from 48 to 3 diametral pitch. They are all designed to increase output, reduce costs and avoid the need for custom specials.
47-MM-OD PILLOW BLOCK FLANGE (SET)-IBI47PBST>
1-VP-50X7/8 Single Groove Variable Pitch Sheaves
he principle of a variable pitch sheave is that the threaded angular faced discs forming the V-shaped groove in which the belt rides are movable. VP sheaves consist of a male with a threaded barrel, and a female with a threaded bore. The male section with threaded barrel has flat surfaces at 180 degree increments that allow a flat surface for the setscrew to mate with. When the discs are moved toward each other, the belt rides higher in the groove and the pitch diameter of the sheave is larger which increases the driven speed. When the discs are moved away from each other, the belt rides lower and the pitch diameter is smaller decreasing the driven speed. The common term for this speed adjustment is called "Number Of Turns Open From Closed Position"
VP single and double groove sheaves, designed for heavier duty service up to 25 hp.
Any standard Browning Sheave can be used as a Companion Sheave.
1 Groove, Finished Bore, Variable Pitch, Cast Iron Sheave, for 3L, 4L or A, 5L or B Section Belt
Type of Bore: Finished
Bore Size: 7/8"
2-VP-56X1-1/8 2-grv Variable Pitch Sheaves
2-GRV VARIABLE PITCH SHEAVES -BRW2VP56X11/8 >
Browning® offers a comprehensive line of off the shelf gears, including spur, miter and bevel as well as change gears. These are available in 20 deg pressure angle from 20 to 4 diametral pitch and 14.5 deg pressure angle from 48 to 3 diametral pitch. They are all designed to increase output, reduce costs and avoid the need for custom specials.
Remke Tuff-Seal™ 7303-014R Closed Mesh Insulated Single Weave Wide Range Strain Relief Grip With Galvanized Steel Mesh, 1.2 to 1.5 in Cable, For Use With 1-1/2 in NPT Connector, Aluminum
Tuff-Seal™ Wire Mesh Cable Grips distribute stress over a large area to prevent damage to wire, cable and flexible conduit. They are built to perform their task over an extended period of time without loosening their hold. All Remke wire mesh grips are available in a wide selection of cable ranges and eye styles where applicable and can be used in conjunction with any RSR cord connector.
