MORSE C/Tool 5/8" FINISHING ROUGHING ENDMILLS MCT 45314
MORSE® 45314 4640C Center Cutting Regular Length Roughing End Mill, 5/8 in Dia Cutter, 2-1/2 in Length of Cut, 4 Flutes, 5/8 in Dia Shank, 4-5/8 in OAL, TiCN Coated
-
BrandMORSE®
-
UPC686125453145
-
Manufacturer Part Number45314
-
CountryUSA
-
FinishTiCN Coated
-
MaterialM42 HSS-Co 8
-
Flute TypeSpiral
-
TypeCenter Cutting Regular Length
-
Helix Angle30 deg
-
Series4640C
-
Cutter Diameter5/8 in
-
Shank Diameter5/8 in
-
Number of Flutes4
-
Cutting DirectionRight Hand
-
Shank TypeRound/Weldon Flat
-
Length of Cut2-1/2 in
-
Overall Length4-5/8 in
- Roughing/finishing end mills rough and finish in a single pass, removing material at roughing rates while producing a finish near that produced by standard end mills
- Recommended for a wide variety of materials of soft to medium hardness including titanium and aluminum alloys
- M42 8% cobalt offers increased wear and heat resistance for abrasive and difficult materials, higher speeds and feeds and long life in production applications
- Tool coatings further enhance milling performance
-
UNSPSC23242511
-
Package Description1/PK
-
Standards/ApprovalsISO 9001:2008
Recently Viewed
MORSE® 45314 4640C Center Cutting Regular Length Roughing End Mill, 5/8 in Dia Cutter, 2-1/2 in Length of Cut, 4 Flutes, 5/8 in Dia Shank, 4-5/8 in OAL, TiCN Coated
United Abrasives-SAIT 84916 DAF Sanding Sheet, 11 in L x 9 in W, 220 Grit, Aluminum Oxide Abrasive, Cloth Backing
CRC® 02018 Lectra Clean® Heavy Duty Non-Flammable Electrical Parts Degreaser, 20 oz Aerosol Can, Irritating Odor/Scent, Clear, Liquid Form
Effectively removes contaminants to increase operating efficiency of energized electrical equipment. It evaporates quickly, leaves no residue and has no flash or fire point. Designed and labeled to be used on equipment where energy and/or residual exists during cleaning.
IKO manufactures a wide range of radial Needle Roller Bearings to meet the needs of different applications and machine profiles. These include shell type bearings, needle roller cages for both general use and within engine connecting rods and machined type Needle Roller Bearings. Shell type Needle Roller Bearings are lightweight, low profile motion components designed to handle either high speeds or heavy loads, depending on the configuration. An outer ring made of high strength steel enables a streamlined profile with the lowest sectional height of all the Needle Roller Bearings.
Morse MHS04P (177795), 8 piece, plumbers hole saw kit contains bimetal hole saw diameters that allow pipe pass through, and tapping, of common diameters of black iron, copper and PVC/ABS. Kit includes 3/4", 7/8", 1-1/8", 1-1/2", 1-3/4", and 2-1/4" diameter, bimetal hole saws, one (1) MA34, 3/8" shank (1/2"-20) standard arbor, one (1) MA45PSN, 1/2" shank (5/8-18) pin drive arbor, and carrying case.
Weiler® 03100 TL-7 Wide Face Wheel Brush, 7 in Dia Brush, 1-1/4 in W Face, 0.014 in Dia Filament/Wire Crimped Filament/Wire, 2 in Arbor Hole
Weiler® 03100 TL-7 Wide Face Wheel Brush, 7 in Dia Brush, 1-1/4 in W Face, 0.014 in Dia Filament/Wire Crimped Filament/Wire, 2 in Arbor Hole
