Drillco 73A108C 7300 Center Cutting Imperial Regular Length Single End Finishing End Mill, 1/8 in Dia Cutter, 3/8 in Length of Cut, 4 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
-
BrandDrillco
-
UPC045997390789
-
Manufacturer Part Number73A108C
-
CountryUSA|Canada
-
FinishUncoated
-
MaterialSolid Carbide
-
Flute TypeSpiral
-
TypeCenter Cutting Imperial Regular Length Single End
-
Helix Angle30 deg
-
Series7300
-
Cutter Diameter1/8 in
-
Shank Diameter1/8 in
-
Number of Flutes4
-
Cutting DirectionRight Hand
-
Shank TypeRound
-
Length of Cut3/8 in
-
Overall Length1-1/2 in
- Solid carbide construction for extreme rigidity and strength
- Solid carbide can be ran at 3x the speed and feed of HSS
- Center cutting tip for plunging, pocketing and holemaking
- 4 flutes produce a better surface finish and less chatter
- Bright finish for added lubricity
-
UNSPSC27112803
-
Package Description1/PK
-
Standards/ApprovalsPROP65: This product can expose you to chemicals including Cobalt, which is [are] known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
-
SDS
-
Catalog
Recently Viewed
Drillco 73A108C 7300 Center Cutting Imperial Regular Length Single End Finishing End Mill, 1/8 in Dia Cutter, 3/8 in Length of Cut, 4 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
Drillco 735A120C 7350 Center Cutting Extra Long Length Imperial Single End Finishing End Mill, 5/16 in Dia Cutter, 1-5/8 in Length of Cut, 4 Flutes, 5/16 in Dia Shank, 4 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Extra long
FLEXCOIL POLYURETHANE AIR HOSE ASSEMBLIES
I.D. X O.D.--3/8" X 9/16"
LENGTH--30'
MPT FITTING--(2) 3/8" SWIVEL
COLOR--DARK BLUE
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
50-B-18-F-1-1/8 18 Tooth Sprockets For #50
18 TOOTH SPROCKETS FOR #50 CHAIN-IDC50B18F11/8 >
