Drillco 74A108C 7400 Center Cutting Double End Imperial Stub Length Finishing End Mill, 1/8 in Dia Cutter, 1/4 in Length of Cut, 2 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
-
BrandDrillco
-
UPC045997391151
-
Manufacturer Part Number74A108C
-
CountryUSA|Canada
-
FinishUncoated
-
MaterialSolid Carbide
-
Flute TypeSpiral
-
TypeCenter Cutting Double End Imperial Stub Length
-
Helix Angle30 deg
-
Series7400
-
Cutter Diameter1/8 in
-
Shank Diameter1/8 in
-
Number of Flutes2
-
Cutting DirectionRight Hand
-
Shank TypeRound
-
Length of Cut1/4 in
-
Overall Length1-1/2 in
- Solid carbide construction for extreme rigidity and strength
- Solid carbide can be ran at 3x the speed and feed of HSS
- Center cutting tip for plunging, pocketing and holemaking
- 2 flutes provide more efficient chip removal
- Bright finish for added lubricity
- Stub length for added rigidity
- Double ended for 2x the life
-
UNSPSC27112803
-
Package Description1/PK
-
Standards/ApprovalsPROP65: This product can expose you to chemicals including Cobalt, which is [are] known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
-
SDS
-
Catalog
Recently Viewed
Drillco 74A108C 7400 Center Cutting Double End Imperial Stub Length Finishing End Mill, 1/8 in Dia Cutter, 1/4 in Length of Cut, 2 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
ALAN 14-THHN ORANGE STRANDED WIRE. THE THHN CONDUCTORS ARE PRIMARILY USED IN CONDUIT AS BRANCH CIRCUITS IN COMMERCIAL OR INDUSTRIAL APPLICATIONS.
TYPE THHN IS AVAILABLE STRANDED IN SIZES 14 AWG -750 KCMIT. THE CONDUCTORS ARE SOFT-ANNEALED, STRANDED OR SOLID COPPER AND ARE INSULATED WITH A TOUGH HEAT AND MOISTURE-RESISTANT POLYVINYL CHLORIDE, OVER WHICH A NYLON JACKSON IS APPLIED.
-ALE14THHNORG >
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
1-1/4" PVC TRU-UNION BALL VALVE-NIBU45TBE11/4 >
Synchronous belt drives help reduce the problems of slippage, belt stretch, lubrication and metal to metal contact. They provide superior performance because power is transmitted by positive engagement of belt teeth rather than by friction, as in conventional belt drives.
The McGill® CAMROL® full complement needle bearings feature black oxide treated bearing steel. They are available in two basic mounting styles for use in mechanical automation or linear motion applications. Our basic features each contribute to superior performance. The LUBRIDISC® seal option helps prevent metal to metal contact within the bearing. It also provides a barrier for containment entry and blowout protection when relubricating. These bearings are available with several dimensional choices. The seal options and combinations provide a specific solution for each application. Within the following section you can learn more about these features and how they can be applied to your application.
