Drillco 72A104C 7200 Center Cutting Imperial Regular Length Single End Finishing End Mill, 1/16 in Dia Cutter, 3/16 in Length of Cut, 2 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
-
BrandDrillco
-
UPC045997390017
-
Manufacturer Part Number72A104C
-
CountryUSA|Canada
-
FinishUncoated
-
MaterialSolid Carbide
-
Flute TypeSpiral
-
TypeCenter Cutting Imperial Regular Length Single End
-
Helix Angle30 deg
-
Series7200
-
Cutter Diameter1/16 in
-
Shank Diameter1/8 in
-
Number of Flutes2
-
Cutting DirectionRight Hand
-
Shank TypeRound
-
Length of Cut3/16 in
-
Overall Length1-1/2 in
- Solid carbide construction for extreme rigidity and strength
- Center cutting tip for plunging, pocketing and holemaking
- Solid carbide can be ran at 3x the speed and feed of HSS
- 2 flutes provide more efficient chip removal
- Bright finish for added lubricity
-
UNSPSC27112803
-
Package Description1/PK
-
Standards/ApprovalsPROP65: This product can expose you to chemicals including Cobalt, which is [are] known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
-
SDS
-
Catalog
Recently Viewed
Drillco 72A104C 7200 Center Cutting Imperial Regular Length Single End Finishing End Mill, 1/16 in Dia Cutter, 3/16 in Length of Cut, 2 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
Drillco 75A112C 7500 Center Cutting Double End Imperial Stub Length Finishing End Mill, 3/16 in Dia Cutter, 3/8 in Length of Cut, 4 Flutes, 3/16 in Dia Shank, 2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
Dichtomatik 75102159 O-Ring, 237 Dash Number, 3.359 in ID x 3.637 in OD, FKM, 75 Shore A Durometer, Import, Custom 237-VITON
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Drillco 75A108C 7500 Center Cutting Double End Imperial Stub Length Finishing End Mill, 1/8 in Dia Cutter, 1/4 in Length of Cut, 4 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
Dichtomatik 75102151 O-Ring, 229 Dash Number, 2.359 in ID x 2.637 in OD, FKM, 75 Shore A Durometer, Import, Custom 229-VITON
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Drillco 75A120C 7500 Center Cutting Double End Imperial Stub Length Finishing End Mill, 5/16 in Dia Cutter, 1/2 in Length of Cut, 4 Flutes, 5/16 in Dia Shank, 2-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
