Hougen® 12232 12000 Annular Cutter, 1 in Dia Cutter, 2 in D Cutting, M2 HSS, Bright, Weldon with 2-Flat Shank
Hougen "12000 Series" cutters were the original annular cutters invented over 35 years ago. With the most features of any annular cutter, "12000 Series" cutters provide the best performance in the largest variety of materials. Compared to traditional tooling (twist drills, etc.) "12000 Series" cutters can multiply your cutting speed by up to 3 times. And you get longer tool life, a more accurate hole, a better finish, with no burrs. Hougen cutters maximize feed rates because up to 10 cutting edges distribute the cutting load evenly. "12000 Series" cutters convert a smaller area to chips, requiring less horsepower and thrust.
-
BrandHougen®
-
UPC662850002698
-
Manufacturer Part Number12232
-
CountryUSA
-
FinishBright
-
MaterialM2 HSS
-
Applicable MaterialsMild Steel, Structural Steel, Aluminum, Stainless Steel, Ferrous and Non-Ferrous Materials
-
Cutter Diameter1 in
-
Cutting Depth2 in
- Ground and fully fluted - Provides better chip evacuation, requires less hp and offers better performance in deeper holes
- Two flats for cutter mounting - This system is very rigid and offers up to 2x the tool life as compared to quick change tool mounting on competitive products
- OD Margin - Only a thin area of material touches the outside of the hole which provides for less friction and a better hole finish
- ID Taper - Relief area between slug and cutter
- The Hougen-Edge® feature is a patented tooth geometry that provides long tool life, less chatter and extended resharpenability
- The slug also offers a higher scrap value than loose chips
- For use with 10528 pilot
- For use with Hougen® portable magnetic drills and many competitive models on materials up to 6 in thick
- They are made from hardened M2 high speed steel and are precision-ground for excellent performance throughout the cut and long tool life
| Competitor Name | Competitor Part Number |
|---|---|
| Berkshire eSupply | FZ8012232 |
| Berkshire eSupply | FZ8012232 |
-
UNSPSC23241600
-
Catalog
-
Owners/User Manual
Recently Viewed
Hougen® 12232 12000 Annular Cutter, 1 in Dia Cutter, 2 in D Cutting, M2 HSS, Bright, Weldon with 2-Flat Shank
Hougen "12000 Series" cutters were the original annular cutters invented over 35 years ago. With the most features of any annular cutter, "12000 Series" cutters provide the best performance in the largest variety of materials. Compared to traditional tooling (twist drills, etc.) "12000 Series" cutters can multiply your cutting speed by up to 3 times. And you get longer tool life, a more accurate hole, a better finish, with no burrs. Hougen cutters maximize feed rates because up to 10 cutting edges distribute the cutting load evenly. "12000 Series" cutters convert a smaller area to chips, requiring less horsepower and thrust.
Lift-All® 6TQSNX1 6TQSN Tubular Quick Sleeve Wearpad, 1 ft L x 6 in W x 3/16 in THK, Webmaster 1600 Nylon
Wear protection products extend the life of slings by reducing exposure to abrasion and other similar forms of sling damage. Wear pads also help protect load surfaces from damage along points of contact.
Sealmaster® 711014 ER Series Non-Expansion Standard Duty Straight Bore Ball Bearing Insert With Snap Ring, 1-1/4 in Dia Bore, 2.4409 in OD, 1 Rows, 1-1/2 in W, 4381 lb Dynamic/2567 lb Static Load
Sealmaster® gold ER bearings feature a cylindrical OD and snap ring for easy installation in a roll assembly. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction.
Hougen® 12221 12000 Annular Cutter, 21/32 in Dia Cutter, 2 in D Cutting, M2 HSS, Bright, Weldon with 2-Flat Shank
Hougen "12000 Series" cutters were the original annular cutters invented over 35 years ago. With the most features of any annular cutter, "12000 Series" cutters provide the best performance in the largest variety of materials. Compared to traditional tooling (twist drills, etc.) "12000 Series" cutters can multiply your cutting speed by up to 3 times. And you get longer tool life, a more accurate hole, a better finish, with no burrs. Hougen cutters maximize feed rates because up to 10 cutting edges distribute the cutting load evenly. "12000 Series" cutters convert a smaller area to chips, requiring less horsepower and thrust.
Hougen® 17832 Imperial Stack-Cut Geometry Annular Cutter, 1 in Dia Cutter, 1 in D Cutting, M42 HSS, Bayonet Style Twist Lock Shank
RotaLoc Plus™ Annular Cutters are designed for the Hougen® HMD130 low profile drill. They're made of M42 HSS, feature stack cut geometry for penetrating multiple plates in a single pass and are designed for a full 1 in depth of cut. They feature a 5/8 in bayonet style shank mounting for fast change out, with no tools required to install in the drill spindle and can be as easily removed. For optimum cutter tool life and cutter efficiency use Hougen® Slick-Stik™ lubricant or RotaGel™ cutting lube.
Lift-All® 8TQSBNX1 8TQSBN Tubular Quick Sleeve Wearpad, 1 ft L x 8 in W x 1/16 in THK, Ballistic Nylon
Wear protection products extend the life of slings by reducing exposure to abrasion and other similar forms of sling damage. Wear pads also help protect load surfaces from damage along points of contact.
