MORSE® 11378 1330 General Purpose Jobber Length Drill Bit, 3/64 in Drill - Fraction, 0.0469 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MORSE® 11378 1330 General Purpose Jobber Length Drill Bit, 3/64 in Drill - Fraction, 0.0469 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
-
BrandMORSE®
-
UPC686125113780
-
Manufacturer Part Number11378
-
CountryUSA
-
FinishBlack Oxide
-
Point Angle118 deg
-
Point TypeStandard
-
MaterialHSS
-
Through Coolant (Yes/No)No
-
Flute Length3/4 in
-
Flute TypeStandard
-
TypeGeneral Purpose
-
Series1330
-
Cutting Depth3/4 in
-
Shank Size3/64 in
-
Cutting DirectionRight Hand
-
Cutting Edge MaterialHSS
-
Shank TypeStraight
-
Drill Diameter Measurement SystemImperial
-
Drill Size - Decimal Inch0.0469 in
-
Drill Size - Fraction3/64 in
-
Overall Length1-3/4 in
- Black oxide surface treatment increases wear resistance, reduces galling and chip welding, improves chip flow and increase drill lubricant retention
| Competitor Name | Competitor Part Number |
|---|---|
| Berkshire eSupply | MT1011378 |
-
UNSPSC23241606
-
Package Description1/PK
-
Standards/ApprovalsNSF Listed
-
Specification Sheet
Recently Viewed
MORSE® 11378 1330 General Purpose Jobber Length Drill Bit, 3/64 in Drill - Fraction, 0.0469 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MORSE® 11378 1330 General Purpose Jobber Length Drill Bit, 3/64 in Drill - Fraction, 0.0469 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MORSE® 16771 1391 Aircraft Extension Drill, #42 Drill - Wire, 0.0935 in Drill - Decimal Inch, 135 deg Point, HSS
MORSE® 16771 1391 Aircraft Extension Drill, #42 Drill - Wire, 0.0935 in Drill - Decimal Inch, 135 deg Point, HSS
IKO LRB121612 Inch Series Inner Ring With Oil Groove, 3/4 in ID x 1 in OD, 19.3 mm OAW, For Use With BR162412 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
MARXMAN™ 85068 330QI General Purpose Jobber Length Drill Bit, #14 Drill - Wire, 0.182 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MARXMAN™ 85068 330QI General Purpose Jobber Length Drill Bit, #14 Drill - Wire, 0.182 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
7 LB BOX OF CEMENT BASE WITH SILICA SAND RESULTING IN DENSE, HARD JOINTS WITHOUT CRACKING OR SHRINKING. PEWTER. SOLD IN-JWH284637 >
Browning® offers a variety of bushing type sprockets available in single and double strands. Offerings include 35 to 160 pitch range. Bushed type bore ranges are available from 1/2 to 5 in. Hardened teeth are available up to 30 teeth.
