Browning® 1296433 Automatic Torque Limiter, 1 in Straight Bore, 4-1/2 in OD, 2800 in-lb (1 Spring)/4900 in-lb (2 Spring) Torque
Browning® torque limiters are torque control devices that slip under excessive load but automatically carry the desired load after the excess has been removed. The device can be easily adjusted to slip at a desired overload and automatically re-engage when overload is removed. Overload should be removed promptly since prolonged slippage can be detrimental to the friction disc. Generally, no resetting is required after the torque limiter has slipped. Torque limiters help prevent machine and product damage and costly downtime caused by shock loads, overloads or machine jams but should not be used as clutches.
-
BrandBrowning®
-
UPC662289221684
-
Manufacturer Part Number1296433
-
CountryUSA
-
Maximum Speed1000 rpm
-
Torque Rating2800 in-lb (1 Spring)/4900 in-lb (2 Spring)
-
TypeAutomatic
-
Minimum Sprocket Teeth32 (NO. 40 Chain), 26 (NO. 50 Chain), 22 (NO. 60 Chain)
-
Outside Diameter4-1/2 in
-
Bore Diameter1 in
-
Bore TypeStraight
-
Overall Length2-3/4 in
- High accuracy
- Low cost
- Compact and reversible
- Non-asbestos pads
- Model T45L
- Morse and Browning offer a complete line of Torque Overload Devices to protect machinery from overloads or jams
- Browning torque limiters slip under excessive load but automatically carry the desired load after the excess has been removed
- Browning offers a complete set of replacement shear pins
- Shear pins are available in a wide range of minimum shear strength
- Browning torque limiters are friction type devices that reset to any position
-
Alternative Part NumberT45LX1
-
UNSPSC41114510
-
Package DescriptionEACH
-
Warranty1 Year
-
Instruction/Installation Manual
Recently Viewed
Browning® 1296433 Automatic Torque Limiter, 1 in Straight Bore, 4-1/2 in OD, 2800 in-lb (1 Spring)/4900 in-lb (2 Spring) Torque
Browning® torque limiters are torque control devices that slip under excessive load but automatically carry the desired load after the excess has been removed. The device can be easily adjusted to slip at a desired overload and automatically re-engage when overload is removed. Overload should be removed promptly since prolonged slippage can be detrimental to the friction disc. Generally, no resetting is required after the torque limiter has slipped. Torque limiters help prevent machine and product damage and costly downtime caused by shock loads, overloads or machine jams but should not be used as clutches.
ISOSTATIC™ Century® 104035 Round Bore Sleeve Bearing, 3/8 in Dia Bore, 5/8 in OD, 1 in W
2-1/2" CARLON ELECTRIC MALE ADAPTER-JWH515795 >
1/2" PVC CARLON ELECTRIC ELBOW-JWH512350 >
The Littelfuse® LGR and LMF series fuses and LHR holder offer increased safety and reliability to lighting systems. on a 277 volt system, a fault occurring in an un-fused fixture could take out the entire branch circuit affecting upto 100 fixtures. this could cause safety problems as well as shut down operations. by individually fusing fixtures, these problems will be avoided. The added benefits of this is the ability to quickly identify the problem fixture and reduce the repair time. fuse holders are rated upto 10 A at 300 V and are equipped with 7 18 AWG leads. Order part number LHR 000 for two leads and part number LHR 001 for one lead and one terminal for insertion of 18 AWG ballast lead.
1-1/2" PVC CARLON ELECTRIC ELBOW-JWH512467 >
