Gates® Power Transmission 1422V440 Bandless Multi-Speed V-Belt, 7/8 in W Top, 22 deg Groove, 44-1/2 in L Outside, Rubber
Power transmission systems do more than operate at constant speeds with constant outputs. Customers increasingly need variable speed systems to regulate the speed and rotational force, or output torque, of critical mechanical equipment. Our Multi-Speed belts are engineered for efficiency, energy savings and increased productivity at a wide range of speeds and speed ratios.
-
BrandGates® Power Transmission
-
UPC72053233186
-
Manufacturer Part Number1422V440
-
CountryUSA|Canada
-
MaterialRubber
-
Top Width7/8 in
-
Reinforced MaterialPolyester
-
TypeBandless
-
Groove Angle22 deg
-
Series9804
-
Outside Length44-1/2 in
- Notch design reduced thermal and bending stresses for longer life
- Smooth running construction for minimal vibration at high speeds
-
Alternative Part Number98040817
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Gates® Power Transmission 1422V440 Bandless Multi-Speed V-Belt, 7/8 in W Top, 22 deg Groove, 44-1/2 in L Outside, Rubber
Power transmission systems do more than operate at constant speeds with constant outputs. Customers increasingly need variable speed systems to regulate the speed and rotational force, or output torque, of critical mechanical equipment. Our Multi-Speed belts are engineered for efficiency, energy savings and increased productivity at a wide range of speeds and speed ratios.
Browning 2-1/2"-ID 2-BOLT TRB PILLOW BLOCKS BRW PBE-920 X 2-1/2
Browning® E920 series mounted tapered roller bearings feature durable 1-piece non-expansion housings with Type E mounting dimensions and limited misalignment. The E920 series contains setscrew locking collars for easy installation. It also contains a contact face riding seal in order to provide a good balance between contaminant entry, grease retention and friction. Depending on your application requirements, these bearings are available in a wide variety of bore sizes and housing configurations.
IKO LRB141816 Inch Series Inner Ring With Oil Groove, 7/8 in ID x 1-1/8 in OD, 25.65 mm OAW, For Use With BR182616 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
BLADE CLAMP SCREWS-MWK06832960 >
Gates® Power Transmission 1422V540 Bandless Multi-Speed V-Belt, 7/8 in W Top, 22 deg Groove, 54.8 in L Outside, Rubber
Power transmission systems do more than operate at constant speeds with constant outputs. Customers increasingly need variable speed systems to regulate the speed and rotational force, or output torque, of critical mechanical equipment. Our Multi-Speed belts are engineered for efficiency, energy savings and increased productivity at a wide range of speeds and speed ratios.
WATTS® 0066107 100XL Self-Closing Temperature and Pressure Relief Valve, 3/4 in Nominal, MNPT x FNPT End Style, 150 psi Pressure, 180 deg F, 3 in L Probe, Brass Body
This 3/4 inch temperature and pressure relief valve is used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 105,000 BTU/hr. It features a brass body with NPT male inlet and NPT female outlet connections, 8 inch extension thermostat with special thermo-bonded coating, and a test lever. It is ASME rated and CSA listed. The temperature relief is at 180 degrees F, and the pressure relief is 150 psi (10.6 bar).
