Gates 4-GROOVE BANDED 3-VX-670 V-BELTS GAT 4/3-VX-670
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
-
BrandGates® Power Transmission
-
UPC72053277302
-
Manufacturer Part Number4/3VX670
-
CountryUSA|Canada
-
Temperature Range-60 to 250 deg F
-
Thickness21/64 in
-
MaterialEPDM
-
Top Width3/8 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeHeavy Duty Molded Notch
-
Minimum Pulley Diameter3.82 in
-
Section Size3VX
-
Series9388
-
Number of Ribs4
-
Outside Length67 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- Notches molded into the belt during manufacturing increase flexibility making this belt well suited for drives with smaller diameter sheaves
- The tie band assures high lateral rigidity, guiding the belt in a straight line and preventing it from coming off the drive
- Patented ethylene material construction provides -60 to 250 deg F temperature range to resist belt cracking
-
Alternative Part Number93884067
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Catalog
-
Instruction/Installation Manual
-
Specification Sheet
Recently Viewed
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
Browning® Classical Gripbelt® 3693710 B5V® Type 1 Web Single Groove Sheave, Split Taper Bore, 1/2 to 2-7/16 in Dia Bore, 7.08 in OD, 6.6 in (A)/7.1 in (B)/6.9 in (BV) Dia Pitch, 1 in W Face
Browning® Classical Gripbelt® 3693710 B5V® Type 1 Web Single Groove Sheave, Split Taper Bore, 1/2 to 2-7/16 in Dia Bore, 7.08 in OD, 6.6 in (A)/7.1 in (B)/6.9 in (BV) Dia Pitch, 1 in W Face
.217" X .256" X .197" OIL SEAL - CHI400060>
1/2HOSEX10FEMALE FLAT FACE 45DEG-MHDE0810FF45 >
OIL SEALS-.375" X .999" X .250"-CHI3751>
Gates® Power Transmission Tri-Power® PowerBand® 2/BX83 Heavy Duty Molded Notch V-Belt, BX Section, 21/32 in W Top, 86.6 in L Outside, 13/32 in THK, EPDM
Built for superior performance on heavy duty classical cross-section drives. The raw edge, Ethylene Elastomer construction and special notch design makes the Tri-Power belt especially suited for small diameter pulleys and back side idler drives.
