Gates POLYFLEX BELTS GAT 7-M-750
Developed by Gates and produced to patented manufacturing processes, these belts provide more load-carrying capacity at higher speeds to small multiple V-belt precision drives. This results in significant cost savings and improved design freedom.
-
BrandGates® Power Transmission
-
UPC72053302097
-
Manufacturer Part Number7M750
-
CountryUSA|Canada
-
Temperature Range-65 to 180 deg F
-
Thickness7/32 in
-
MaterialHigh Modulus Polyurethane
-
Top Width9/32 in
-
Reinforced MaterialPolyester
-
TypeLight Duty
-
Minimum Pulley Diameter2.546 in
-
Section Size7M
-
Series8903
-
Number of Ribs1
-
Outside Length29.53 in
- High modulus polyurethane compound resists fatigue, wear, ozone and most environmental conditions
- Precise casting method eliminates layers and overlaps for smooth running and low vibration
- Ribbed backing provides greater lateral stability and relieves bending stress
- Unique 60 deg angle polyurethane construction transmits greater loads at higher speeds in less space than conventional V-belts
-
Alternative Part Number89030750
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsRMA Standard
-
Specification Sheet
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Developed by Gates and produced to patented manufacturing processes, these belts provide more load-carrying capacity at higher speeds to small multiple V-belt precision drives. This results in significant cost savings and improved design freedom.
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
Gates® Power Transmission Hi-Power® II B74 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 77 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
Milwaukee® 49-56-2003 Hole Saw, 2 in Dia, 1-5/8 in D Cutting, Tungsten Carbide Cutting Edge
Milwaukee® carbide tipped hole saws provide long life and faster cutting in cement board, ceramic tiles, fiberglass and wood products such as fiberboard, flake board and plywood. Use a carbide tipped pilot bit (49-56-8005) when cutting ceramic tile, brick and other abrasive materials.
MWS-25/200 1/4-hp To 2-hp Dc Motor
1/4-HP TO 2-HP DC MOTOR CONTROLLER-BRWMWS25/200>
Browning® 767561 VPLS 100 Intermediate Duty Low Base Pillow Block Ball Bearing Unit, 3/4 in Dia Bore, 3-31/64 to 4-17/64 in L Bolt Center-to-Center, 1-1/4 in Base to Bore Centerline, 5 in OAL x 2-15/32 in OAH
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric or BOA concentric locking collar. The contact seal with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction.
