ASP-150-2-SSS Industry Standard Clamping Collar, 2-Piece Construction, 1-1/2 in ID x 2-3/8 in OD x 9/16 in W, Stainless Steel
Stainless Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
-
BrandClimax
-
UPC044861630907
-
Manufacturer Part NumberG2SC-150-SS
-
CountryUSA
-
FinishPlain
-
MaterialStainless Steel
-
TypeIndustry Standard
-
Construction2-Piece
-
Screw Size1/4-28 UN-3A x 3/4 in
-
Width9/16 in
-
SeriesG2SC
-
Inside Diameter1-1/2 in
-
Outside Diameter2-3/8 in
- Easily installed where major disassembly would otherwise be required
- Greater axial holding power than setscrew or 1-piece clamping collars
- Effective on hard and soft shafts
- Without recessed screw
- Design fully engages the shaft without marring
-
UNSPSC31162811
-
Package DescriptionEACH
-
Standards/ApprovalsASTM A582|ASTM F837 Cap Screw
-
Specification Sheet
-
Line Drawing
Recently Viewed
ASP-150-2-SSS Industry Standard Clamping Collar, 2-Piece Construction, 1-1/2 in ID x 2-3/8 in OD x 9/16 in W, Stainless Steel
Stainless Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
MORSE® 59889 5970 Premium Carbide Burr, End Cut End, Cylindrical Head, 3/4 in Dia Head, 3/4 in L of Cut, 2-1/2 in OAL, Double Cut
MORSE® 59889 5970 Premium Carbide Burr, End Cut End, Cylindrical Head, 3/4 in Dia Head, 3/4 in L of Cut, 2-1/2 in OAL, Double Cut
NIBCO T-480-Y-1 Standard In-Line Ball Cone Check Valve, 1 in Nominal, FNPT End Style, 6 gpm Flow Rate, Bronze Body, Domestic
The Apollo™ CVB Ball Cone® check valves offer reliable protection against reverse flow and exceptional resistance to chemicals and corrosion using proven ASTM quality materials made in the USA.
10 GALLON ALL PURPOSE MIXING TUB-JWH263011>
Browning® 1045574 VP Series Type 2 Variable Pitch Sheave, 7/8 in Finished Bore, 5.95 in OD, 1 Groove, 4.4 to 5.4 in (A/4L)/4.7 to 5.9 in (B/5L/5V) Dia Pitch, 7/8 to 1-1/4 in W Face
The principle of a variable pitch sheave is that the threaded angular faced discs forming the V-shaped groove in which the belt rides are movable. VP sheaves consist of a male with a threaded barrel, and a female with a threaded bore. The male section with threaded barrel has flat surfaces at 180 deg increments that allow a flat surface for the setscrew to mate with. When the discs are moved toward each other, the belt rides higher in the groove and the pitch diameter of the sheave is larger which increases the driven speed. When the discs are moved away from each other, the belt rides lower and the pitch diameter is smaller decreasing the driven speed. The common term for this speed adjustment is called number of turns open from closed position.
Channellock® 212 Oil Filter/PVC Plier, 4-1/4 in, 2.52 in High Carbon Steel Jaw, 12 in OAL
We combined the strength and reliability of our iconic tongue and groove plier with the special needs of large PVC and oil filters. The Channellock® 212 accommodates most car and light truck filters and fits PVC, conduit and fittings.
