McGill 4"-ID NEEDLE ROLLER BEARINGS MCG MR-64
McGill® CAGEROL® machined race needle bearings are manufactured from bearing quality steel. Most sizes use crowned or end relieved, rollers to help reduce end stresses and allows for greater misalignment. The rollers are separated by a steel retainer (cage) to help achieve higher speeds and provide a lubricant reservoir. CAGEROL® bearings are constructed with radial lubrication hole and groove on the outer and optional inner raceway (MI series) for relubrication through the housing or shaft. Other options include a variety of seal configurations to either help prevent contaminant entry or contain the lubricant.
-
BrandMcGill®
-
UPC726166064426
-
Manufacturer Part Number5406400000
-
CountryUSA
-
Load Capacity38000 lb Dynamic/93800 lb Static
-
Cage MaterialSteel
-
Temperature Rating-20 to 250 deg F
-
Maximum Speed3000 rpm
-
Closure TypeUnsealed
-
TypeHeavy Duty Standard
-
Width2 in
-
SeriesMR Series
-
Number of Rows1
-
Bearing Material52100 Steel
-
Outside Diameter5 in
-
Bore Diameter4 in
- Machined outer race
- Needle roller with end relief
- Annular lubrication groove and holes
- Factory grease f
-
Alternative Part NumberMR 64
-
UNSPSC31171542
-
Package DescriptionEACH
-
Catalog
-
Specification Sheet
Recently Viewed
McGill® CAGEROL® machined race needle bearings are manufactured from bearing quality steel. Most sizes use crowned or end relieved, rollers to help reduce end stresses and allows for greater misalignment. The rollers are separated by a steel retainer (cage) to help achieve higher speeds and provide a lubricant reservoir. CAGEROL® bearings are constructed with radial lubrication hole and groove on the outer and optional inner raceway (MI series) for relubrication through the housing or shaft. Other options include a variety of seal configurations to either help prevent contaminant entry or contain the lubricant.
Proto® DuraTek™ JC31605R Screwdriver, 3/16 in Cabinet/Slotted Point, Alloy Steel Shank, 9-1/4 in OAL, Black Oxide/Polished Chrome, ASME B107.15
POST BACKFILL CONCRETE ALTERNATIVE-JWH260555>
The wheel pin is universal to all REED LCRC and RC cutters. It is used to hold the wheel in place and allows for easy change of wheels, whether from old to new, or from wheels for steel to wheels for cast/ductile iron, which gives these cutters their useful versatility. (Note: the RC36S and RC42S cutters are only for steel.) REED strongly recommends changing all four cutter wheels simultaneously for optimum cutter performance. The 93220 outboard roller is for use with all cutter wheels except the RCX wheel. Each cutter wheel requires two outboard rollers for a total of eight per cutter. The 93222 outboard roller is a specially designed roller for use with the RCX wheel only. When using RCX wheels, it is critical to change the outboard rollers from 93220 and use only the 93222 roller. The RCX wheels are designed to cut thicker-walled pipe, and the 93222 roller has a smaller diameter, which allows the longer profile of the RCX wheel to penetrate steel or stainless pipe wall up to 0.8 inches (20.3 mm). As with all LCRC or RC cutters, a total of eight outboard rollers is required per cutter. To cut only thicker-walled steel or stainless steel pipe, order cutters with the "X" designation (such as LCRC8X), because these come automatically equipped with the RCX wheels and 93222 rollers.
Hougen "12000 Series" cutters were the original annular cutters invented over 35 years ago. With the most features of any annular cutter, "12000 Series" cutters provide the best performance in the largest variety of materials. Compared to traditional tooling (twist drills, etc.) "12000 Series" cutters can multiply your cutting speed by up to 3 times. And you get longer tool life, a more accurate hole, a better finish, with no burrs. Hougen cutters maximize feed rates because up to 10 cutting edges distribute the cutting load evenly. "12000 Series" cutters convert a smaller area to chips, requiring less horsepower and thrust.
Browning® 1072933 Weld-On Hub, 1-3/4 in OAL, Sintered Steel/Malleable Iron/Ductile Iron
Browning® 1072933 Weld-On Hub, 1-3/4 in OAL, Sintered Steel/Malleable Iron/Ductile Iron
