IKO BA1812ZOH Inch Series Caged Shell Standard Needle Roller Bearing With Oil Hole and Dust Cover, 1-1/8 in Dia Bore, 1-3/8 in OD, 1 Row, 3/4 in W, 15000 N Dynamic/26900 N Static Load
IKO manufactures a wide range of radial Needle Roller Bearings to meet the needs of different applications and machine profiles. These include shell type bearings, needle roller cages for both general use and within engine connecting rods and machined type Needle Roller Bearings. Shell type Needle Roller Bearings are lightweight, low profile motion components designed to handle either high speeds or heavy loads, depending on the configuration. An outer ring made of high strength steel enables a streamlined profile with the lowest sectional height of all the Needle Roller Bearings.
-
BrandIKO
-
Manufacturer Part NumberBA1812ZOH
-
CountryUSA
-
Load Capacity15000 N Dynamic/26900 N Static
-
Maximum Speed13000 rpm
-
Closure TypeOpen
-
Bearing MaterialChromium Molybdenum Steel
-
Bore Diameter1-1/8 in
- Caged bearings for high-speed rotation feature precise needle rollers, accurately guided by a cage and thrust rings
-
UNSPSC31171512
-
Catalog
Recently Viewed
IKO BA1812ZOH Inch Series Caged Shell Standard Needle Roller Bearing With Oil Hole and Dust Cover, 1-1/8 in Dia Bore, 1-3/8 in OD, 1 Row, 3/4 in W, 15000 N Dynamic/26900 N Static Load
IKO manufactures a wide range of radial Needle Roller Bearings to meet the needs of different applications and machine profiles. These include shell type bearings, needle roller cages for both general use and within engine connecting rods and machined type Needle Roller Bearings. Shell type Needle Roller Bearings are lightweight, low profile motion components designed to handle either high speeds or heavy loads, depending on the configuration. An outer ring made of high strength steel enables a streamlined profile with the lowest sectional height of all the Needle Roller Bearings.
Climax G2SC-187-B Industry Standard Clamping Collar, 2-Piece Construction, 1-7/8 in ID x 2-7/8 in OD x 11/16 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
Damar® 00117D Incandescent Bulb, 25 W, E26 Medium A19 Lamp
18" FLEXIBLE COPPER WITH HEATER LINE-JWH407223 >
RUS-KIL VISTA GREEN SPRAY PAINT-BLP1041S >
Browning® 1296516 T55L Automatic Torque Limiter, 1-1/4 in Finished Bore, 5-1/2 in OD, 3800 in-lb (1-Spring)/6800 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
