Sealmaster® 700616 SP Series Standard-Duty Pillow Block Ball Bearing Unit, 1-15/16 in Dia Bore, 6-3/4 to 8-1/2 in L Bolt Center-to-Center, 2-3/4 in Base to Bore Centerline, 10-1/2 in OAL x 5-5/16 in OAH
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
-
BrandSealmaster®
-
UPC662461005002
-
Manufacturer Part Number700616
-
CountryUSA
-
Load Capacity7889 lb Dynamic
-
Locking DeviceSet Screw
-
Temperature Rating250 deg F
-
FinishUncoated
-
MaterialCast Iron
-
Maximum Speed3550 rpm
-
TypeStandard-Duty
-
Mounting TypeTwo-Bolt Base
-
Seal TypeFelt
-
SeriesSP Series
-
Base Width2-1/2 in
-
Base to Bore Centerline2-3/4 in
-
Bolt Center-to-Center Length6-3/4 to 8-1/2 in
-
Bore Diameter1-15/16 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height5-5/16 in
-
Overall Length10-1/2 in
-
Overall Width2-1/32 in
- Wide outer ring
- Metal nameplate riveted to the housing allows for easy identification even after years of operation
- GoldPlex®-HP grease
- Alemite fitting lubrication
- 52100 black oxide coated steel bearing
- Powder coated epoxy cast iron housing with extended inner ring bearings
- Zone hardened inner ring with 120 deg spacing setscrew locking with diamond faceted setscrews
- Unique land riding retainer design provides superior pocket clearance that allows for 360 deg grease circulation around the rolling elements resulting in better retained and utilized lubrication
- Sealmaster exclusive lock pin and dimple for direct lubrication and anti-rotation
-
Alternative Part NumberSP-31
-
UNSPSC31171504
-
Package DescriptionEACH
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Sealmaster® 700616 SP Series Standard-Duty Pillow Block Ball Bearing Unit, 1-15/16 in Dia Bore, 6-3/4 to 8-1/2 in L Bolt Center-to-Center, 2-3/4 in Base to Bore Centerline, 10-1/2 in OAL x 5-5/16 in OAH
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
Klein® D366-6C Fatigue Reducing Needle Nose Plier, Knurled Steel Jaw, 1-15/16 in L x 11/16 in W Jaw, 8 in OAL, 1/16 in W Tip
Klein® D366-6C Fatigue Reducing Needle Nose Plier, Knurled Steel Jaw, 1-15/16 in L x 11/16 in W Jaw, 8 in OAL, 1/16 in W Tip
Browning® Classical Gripbelt® 1042605 BK Series Type 3 Single Groove Sheave, Split Taper Bore, 3/8 to 1-1/2 in Dia Bore, 9-1/4 in OD, 8.7 in (A)/9.2 in (B) Dia Pitch, 7/8 in W Face
Browning® Classical Gripbelt® 1042605 BK Series Type 3 Single Groove Sheave, Split Taper Bore, 3/8 to 1-1/2 in Dia Bore, 9-1/4 in OD, 8.7 in (A)/9.2 in (B) Dia Pitch, 7/8 in W Face
FYH® NAP207 23 NAP Normal Duty Pillow Block Unit, 1-7/16 in Dia Bore, 1-7/8 in Base to Bore Centerline, 6-9/16 in OAL 3-3/4 in OAH
FYH® NAP207 23 NAP Normal Duty Pillow Block Unit, 1-7/16 in Dia Bore, 1-7/8 in Base to Bore Centerline, 6-9/16 in OAL 3-3/4 in OAH
FYH® NAPK209 27 NAPK Normal Duty Pillow Block Unit, 1-11/16 in Dia Bore, 5-7/8 in L Bolt Center-to-Center, 2-1/16 in Base to Bore Centerline, 7-15/32 in OAL 4-3/16 in OAH
FYH® NAPK209 27 NAPK Normal Duty Pillow Block Unit, 1-11/16 in Dia Bore, 5-7/8 in L Bolt Center-to-Center, 2-1/16 in Base to Bore Centerline, 7-15/32 in OAL 4-3/16 in OAH
150-WATT SHATTER-SHIELD BULB-BUL150BR38FLSS>
