FYH® NAP208 24 NAP Normal Duty Pillow Block Unit, 1-1/2 in Dia Bore, 1-15/16 in Base to Bore Centerline, 7-1/4 in OAL 3-27/32 in OAH
FYH® NAP208 24 NAP Normal Duty Pillow Block Unit, 1-1/2 in Dia Bore, 1-15/16 in Base to Bore Centerline, 7-1/4 in OAL 3-27/32 in OAH
-
BrandFYH®
-
Manufacturer Part NumberNAP208 24
-
CountryUSA
-
Load Capacity29.1 kN Dynamic/17.8 kN Static
-
Locking DeviceEccentric Collar
-
TypeNormal Duty
-
SeriesNAP
-
Base to Bore Centerline1-15/16 in
-
Bore Diameter1-1/2 in
-
Bore TypeCylindrical
-
Overall Height3-27/32 in
-
Overall Length7-1/4 in
-
Overall Width2-1/8 in
Recently Viewed
FYH® NAP208 24 NAP Normal Duty Pillow Block Unit, 1-1/2 in Dia Bore, 1-15/16 in Base to Bore Centerline, 7-1/4 in OAL 3-27/32 in OAH
FYH® NAP208 24 NAP Normal Duty Pillow Block Unit, 1-1/2 in Dia Bore, 1-15/16 in Base to Bore Centerline, 7-1/4 in OAL 3-27/32 in OAH
Browning® Classical Gripbelt® 1042530 BK Series Type 3 Single Groove Sheave, Split Taper Bore, 3/8 to 1-1/2 in Dia Bore, 6-3/4 in OD, 6.2 in (A)/6.7 in (B) Dia Pitch, 7/8 in W Face
Browning® Classical Gripbelt® 1042530 BK Series Type 3 Single Groove Sheave, Split Taper Bore, 3/8 to 1-1/2 in Dia Bore, 6-3/4 in OD, 6.2 in (A)/6.7 in (B) Dia Pitch, 7/8 in W Face
Browning® Classical Gripbelt® 1042555 BK Series Type 3 Single Groove Sheave, Split Taper Bore, 3/8 to 1-1/2 in Dia Bore, 7-1/4 in OD, 6.7 in (A)/7.2 in (B) Dia Pitch, 7/8 in W Face
Browning® Classical Gripbelt® 1042555 BK Series Type 3 Single Groove Sheave, Split Taper Bore, 3/8 to 1-1/2 in Dia Bore, 7-1/4 in OD, 6.7 in (A)/7.2 in (B) Dia Pitch, 7/8 in W Face
FYH® NAP206 20 NAP Normal Duty Pillow Block Unit, 1-1/4 in Dia Bore, 1-11/16 in Base to Bore Centerline, 6-1/2 in OAL 3-5/16 in OAH
FYH® NAP206 20 NAP Normal Duty Pillow Block Unit, 1-1/4 in Dia Bore, 1-11/16 in Base to Bore Centerline, 6-1/2 in OAL 3-5/16 in OAH
150-WATT 130-VOLT INSIDE FROST BULBS-BUL150A130V >
Sealmaster® 700871 TB Series Standard-Duty Pillow Block Ball Bearing Unit, 1-1/8 in Dia Bore, 3 in L Bolt Center-to-Center, 1-11/16 in Base to Bore Centerline, 4 in OAL x 3-13/32 in OAH
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
