Sealmaster® 705320 Round Bore Standard Duty Ball Bearing Insert, 1-3/4 in Dia Bore, 3.3465 in OD, 2 in W, 7901 lb Dynamic/5139 lb Static Load
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction.
-
BrandSealmaster®
-
UPC662461029183
-
Manufacturer Part Number705320
-
CountryUSA
-
Load Capacity7901 lb Dynamic/5139 lb Static
-
Cage MaterialBrass
-
Temperature Rating-20 to 220 deg F
-
FinishOxide Coated
-
Maximum Speed5300 rpm
-
Closure TypeDouble Seal
-
TypeRound Bore Standard Duty
-
Seal MaterialFelt
-
Width2 in
-
Bearing MaterialChrome Steel
-
Outside Diameter3.3465 in
-
Bore Diameter1-3/4 in
- Wide outer ring
- Lock pin and dimple system
- The felt seal with flinger provides a tight labyrinth seal which retains lubrication and acts as a filter to exclude contamination
- Skwezloc® is a concentric locking collar clamp design that results in near perfect concentricity of the shaft to the bearing bore and maintains near perfect ball path roundness
- Zone hardened inner race
- Land riding retainer
- Lithium complex NLGI #2 grease with an EP additive
-
Alternative Part Number2-112T
-
UNSPSC31171537
-
Package DescriptionEACH
-
Instruction/Installation Manual
-
Specification Sheet
Recently Viewed
Sealmaster® 705320 Round Bore Standard Duty Ball Bearing Insert, 1-3/4 in Dia Bore, 3.3465 in OD, 2 in W, 7901 lb Dynamic/5139 lb Static Load
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction.
JAS540H300>
Dichtomatik N70450 O-Ring, 450 Dash Number, 10.475 in ID x 11.025 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
1/2" SCH-80 CPVC 90-DEGREE ELBOW-NIB1806005 >
Drillco 73A132C 7300 Center Cutting Imperial Regular Length Single End Finishing End Mill, 1/2 in Dia Cutter, 1 in Length of Cut, 4 Flutes, 1/2 in Dia Shank, 3 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
General Pipe Cleaners 50PMH PMH Premium Drain Auger, 3/8 in Dia x 50 ft L Cable, Crank Handle
Increase drain auger sales by ordering Premium Drain Augers with these attractive tamper-resistant plastic display bags. Complete directions on the back in English, French and Spanish. These models have professional-type sliding crank handles with smoothly working hand grips. This feature gives the augers a more attractive, high quality appearance. The handle is formed from heavy-wall tubing and the thumb screw is 1/2 in (13 mm) long x 1/4 in (6 mm) for solid gripping without thread stripping. In addition, the handle has a good offset for greater turning leverage. Made from high tensile bright wire. 1/4 in (6 mm) augers have basin plug head for easy threading through strainer. A 3/8 in (10 mm) and 1/2 in (13 mm) augers have large bulb-shaped corkscrew boring head.
