IKO CR12UU Inch Series Caged Standard Cam Follower With Cylindrical Outer Ring, 3/4 in Dia x 1/2 in W Roller, 3/8 in Dia x 7/8 in L Stud, High Carbon Steel Roller
IKO designs and manufactures a broad selection of Cam Followers to meet the diverse needs of applications including machine tools, industrial robots, electronic parts production and office automation equipment. A Cam Follower is a bearing that incorporates needle style rollers between a stud and a thick outer ring.
-
BrandIKO
-
Manufacturer Part NumberCR12UU
-
CountryUSA
-
Load Capacity4420 N Dynamic/5110 N Static
-
Closure TypeSealed
-
Head TypeScrewdriver Slot
- Small coefficient of friction
- Excellent rotational performance designed for outer ring revolution
- High load capacity by design - radial gap is smaller than within the general needle roller bearings, alleviating impact load and increasing lifetime
- Easy attachment with either hexagon sockets or screw driver slots
- Standard Cam Followers are the basic style and suit a wide range of applications
- Easy lubrication with oil supplied from the stud head with a hexagon socket design
-
UNSPSC31171530
-
Catalog
Recently Viewed
IKO CR12UU Inch Series Caged Standard Cam Follower With Cylindrical Outer Ring, 3/4 in Dia x 1/2 in W Roller, 3/8 in Dia x 7/8 in L Stud, High Carbon Steel Roller
IKO designs and manufactures a broad selection of Cam Followers to meet the diverse needs of applications including machine tools, industrial robots, electronic parts production and office automation equipment. A Cam Follower is a bearing that incorporates needle style rollers between a stud and a thick outer ring.
NIBCO 76-505-01 2-Piece Standard Configuration Ball Valve, 1 in Nominal, FNPT End Style, Standard Port, MPTFE/PTFE Softgoods, Domestic
Apollo™ 7650501A 76-500 2-Piece Standard Configuration Ball Valve, 1 in Nominal, FNPT End Style, Standard Port, MPTFE/PTFE Softgoods, Domestic
ALAN 12-THHN YELLOW STRANDED WIRE. THE THHN CONDUCTORS ARE PRIMARILY USED IN CONDUIT AS BRANCH CIRCUITS IN COMMERCIAL OR INDUSTRIAL APPLICATIONS.
TYPE THHN IS AVAILABLE STRANDED IN SIZES 14 AWG -750 KCMIT. THE CONDUCTORS ARE SOFT-ANNEALED, STRANDED OR SOLID COPPER AND ARE INSULATED WITH A TOUGH HEAT AND MOISTURE-RESISTANT POLYVINYL CHLORIDE, OVER WHICH A NYLON JACKSON IS APPLIED.
-ALE12THHNYEL >
Remke Tuff-Seal™ 7303-002R Closed Mesh Non-Insulated Single Weave Wide Range Strain Relief Grip With Galvanized Steel Mesh, 0.3 to 0.43 in Cable, For Use With 1/2 in NPT Connector, Aluminum
Tuff-Seal™ Wire Mesh Cable Grips distribute stress over a large area to prevent damage to wire, cable and flexible conduit. They are built to perform their task over an extended period of time without loosening their hold. All Remke wire mesh grips are available in a wide selection of cable ranges and eye styles where applicable and can be used in conjunction with any RSR cord connector.
HCI Preferred Supplier 940173 Ball Valve, 1/2 in Nominal, FNPT End Style, Forged Brass Body, Full Port, PTFE Stem Seal Softgoods
HCI Preferred Supplier 940173 Ball Valve, 1/2 in Nominal, FNPT End Style, Forged Brass Body, Full Port, PTFE Stem Seal Softgoods
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
