Nice® 5491VMF53 5000® Round Bore Unground Flanged Radial Ball Bearing, 1/2 in Dia Bore, 1-1/8 in OD, 1 Row, 0.437 in W, 200 lb Load
The 5000® Series of bearings is similar in construction to the 400® Series bearing except it has a flange on the outer ring to locate the bearing when pressed into a tube or housing, thus eliminating the need for an external mounting device. The bearings are designed for moderate loads and speeds where running accuracy and noise level requirements do not warrant the more expensive precision ground bearings. This series of bearings feature a full ball complement without a retainer. The rings are case hardened and the soft steel band on the outer ring of the unitized assembly allows the bearing to be pressed into a housing without the necessity of close housing tolerances. The bearings are supplied pregreased as a standard. The bearings are designed for use in applications with speeds not exceeding 1200 rpm.
-
BrandNice®
-
UPC637400410001
-
Manufacturer Part Number5491VMF53
-
CountryUSA
-
Load Capacity200 lb
-
Temperature Rating300 deg F
-
FinishUncoated
-
Flange Diameter1-1/4 in
-
Maximum Speed1200 rpm
-
Closure TypeOpen
-
TypeRound Bore
-
Width0.437 in
-
Series5000®
-
Number of Rows1
-
Bearing Material52100 Steel
-
Outside Diameter1-1/8 in
-
Bore Diameter1/2 in
- Designed for moderate loads and speeds
- 1010 soft carbon steel band on the outer ring permits the bearing to be pressed into a housing without the necessity of close housing tolerances
- Hardened inner and outer rings
- Full complement of balls for maximum capacity
- Pregreased with metered Shell Alvania #2 grease
- Flanged outer ring to locate the bearing when pressed into a tube or housing
- Fully unitized assembly
- C0 clearance
- No filling slot
- Without cage
- Case hardened carbon steel rings
- Grade 200 carbon steel balls
- Full compliant
- Shell Darina EP2
- Flanged outside ring
- Without snap ring
-
UNSPSC31171504
-
Package Description10/PK
-
Standards/ApprovalsASPR|CAS|DFAR|FAR Standards
-
Warranty90 Days
-
Catalog
Recently Viewed
Nice® 5491VMF53 5000® Round Bore Unground Flanged Radial Ball Bearing, 1/2 in Dia Bore, 1-1/8 in OD, 1 Row, 0.437 in W, 200 lb Load
The 5000® Series of bearings is similar in construction to the 400® Series bearing except it has a flange on the outer ring to locate the bearing when pressed into a tube or housing, thus eliminating the need for an external mounting device. The bearings are designed for moderate loads and speeds where running accuracy and noise level requirements do not warrant the more expensive precision ground bearings. This series of bearings feature a full ball complement without a retainer. The rings are case hardened and the soft steel band on the outer ring of the unitized assembly allows the bearing to be pressed into a housing without the necessity of close housing tolerances. The bearings are supplied pregreased as a standard. The bearings are designed for use in applications with speeds not exceeding 1200 rpm.
Alemite® 1641-B Straight Thread Fitting, 1/4-28 Taper Thread, 35/64 in OAL, 3/16 in L Shank, Trivalent Zinc Plated
Alemite® 1641-B Straight Thread Fitting, 1/4-28 Taper Thread, 35/64 in OAL, 3/16 in L Shank, Trivalent Zinc Plated
Leviton® L7504 Straight Single Weave Wide Range Wire Mesh Strain Relief Grip, 3/4 in Trade, 0.52 to 0.73 in Cable Openings, Steel, Galvanized
Leviton® wire mesh safety grips are built tough to provide the strength, reliability and gripping force required for today's demanding wire management applications. They are designed to distribute stress over a large area so they can securely hold, pull or support the wire, rope, tubing or fiber optic cable to which they are applied. Leviton® wire mesh safety grips are flexible holding devices used to pull cable, rope or tubing into place, to support it after it has been installed, to prevent cable pullout or to provide strain relief that reduces the arc of bend at points of wire connections or terminations. Available in a wide selection of style, weave, attachment and wire options designed to meet the highest standards for strength, flexibility, durability and longevity.
1687/1587 23-A-90-2 #2 OXY-ACETYLENE WELDING TIP - FOR87202>
Remke Tuff-Seal™ RSR-315 Straight Cord Grip Connector, 1 in Trade, 0.812 to 0.938 in Cable Openings, Aluminum
Tuff-Seal™ RSR series aluminum cord grips are UL listed and CSA certified for use in both indoor and outdoor applications to prevent cable pullout, control arc of bend and to provide a tight seal against environmental elements such as dirt, moisture and coolants. The breadth of the line encompasses conduit sizes from 1/4 to 4 in with fittings offered in machined aluminum, nickel plated aluminum, steel, stainless steel, nylon and Valox®.
CHALKBOARD CLEANER-MIS10120>
