OIL SEALS
2.125" X 3.623" X .468" OIL SEAL - NAT455080>
5.875" X 7.125" X .625" OIL SEAL - NAT455075>
4.000" X 5.005" X .468" OIL SEALS-NAT455035>
SCOTSEALS-SCOTSEALS-CHI455031>
3.437" X 5.004" X .468" OIL SEALS-NAT455026>
3.312" X 5.004" X .468" OIL SEAL-NAT455024>
3.187" X 4.254" X .625" OIL SEAL-NAT455017>
2.625" X 3.881" X .468" OIL SEALS-NAT455007>
2.563" X 3.623" X .468" OIL SEAL-NAT455002>
SCOTSEALS-4.500" X 6.441" X .938"-CHI45162>
4.500" X 6.254" X 1.047" SCOTSEALS -CHI45160 >
.968" X 1.503" X .312" OIL SEALS-NAT451583>
SCOTSEALS-4.500" X 6.254" X .750"-CHI45158>
OIL SEALS-4.500" X 6.250" X .500"-CHI45150>
OIL SEALS-4.500" X 6.250" X .500"-IMS45150>
.750" X 1.000" X .630" OIL SEAL-CHI451245 >
4.500" X 6.001" X .500" OIL SEAL-CHI45111 >
OIL SEALS-4.500" X 6.001" X .500"-IMS45110>
4.500" X 6.001" X .500" OIL SEAL-CHI45110 >
SCOTSEALS-4.500" X 5.876" X .984"-IMS45103>
4.500" X 5.876X1.009" SCOTSEAL-CHI45102 >
4.500" X 5.751" X 1.016" SCOTSEAL-CHI45099 >
1.687" X 2.720" X .468" OIL SEALS-NAT450765>
• Inside Diameter (ID): 3.500 inches to 3.750 inches
• Outside Diameter (OD): 5.125 inches to 5.250 inches
• Bolt Hole Configuration: 6 Holes
• Bolt Circle Diameter (BC): 4.500 inches
Recently Viewed
Sealmaster 3-7/16"-ID 4-BOLT BB PILLOW BLOCKS SEA MSFPD-55
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
PW-18-ALUM TEKTON/MICHIGAN INDUSTRIAL TOOLS 18" IMPORTED ALUMINUM PIPE WRENCH
PIPE WRENCHES 18" ALUMINUM PIPE WRENCH-TABPW18ALUM>
5/8" X 18" ROLLING HEAD PRY BAR - ARS70521 >
GENERAL® 160R Reversible Tap Wrench, #0-8 Tap, Ratcheting, Hardened Steel, 2-3/4 in L, Sliding T-Handle Handle
Browning® 1079292 Split Taper Bushing, 1-11/16 in Dia Bore, 2.7032 in Small End/2.875 in Large End Dia Barrel, 4-1/8 in Dia Flange, 3-1/2 in OAL, Sintered Steel
External key provides positive drive with no torque on the cap screws. We offer high torque carrying capacity. Double split barrel improves true concentricity. The shaft is gripped with positive clamp fit.
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
