TL-STYLE BUSHING
45-MM-ID 2012-STYLE TAPER-LOCK BUSHING - IDC201245MM >
50-MM-ID 2012-STYLE TAPER-LOCK BUSHING - IDC201250MM >
2012-7/8 7/8"-ID 2012-style Tl Bushing
7/8"-ID 2012-STYLE TL BUSHING - IDC20127/8>
2012X1-1/2 1-1/2" -ID 2012-style Taper-lock
Browning 1-1/2" Bore, Tapered Lock Sprocket Bushing
Manufacturer Part #: 2012X 1 1/2
1-1/4" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X11/4 >
1-1/8" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X11/8 >
1-1-1/16" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X111/16 >
1-13/16" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X113/16 >
1-15/16" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X115/16 >
2012X1-3/4 1-3/4" -ID 2012-style Taper-lock
2012X134
2012X 1 3/4
TAPER BORE BUSHINGS-900
1-3/8" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X13/8 >
2012X1-5/8 1-5/8" -ID 2012-style Taper-lock
2012X158
2012X 1 5/8
TAPER BORE BUSHINGS-900
1-7/16" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X17/16 >
1-7/8" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X17/8 >
1-9/16" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X19/16 >
1-1/16" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X1.1/16 >
1-3/16" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X1.3/16 >
1-5/16" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X1.5/16 >
1/2" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X1/2 >
1-1/16" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X11/16 >
13/16" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X13/16 >
15/16" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X15/16 >
3/4" -ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X3/4 >
35-MM-ID 2012-STYLE TAPER-LOCK BUSHING-BRW2012X35MM >
Recently Viewed
1-1/4" CARBON HOLE SAW. CUT UP TO 3/4" DEPTH-JWH327093 >
Browning®Type B minimum bore sprockets are offered in single, double and triple strands. Offerings include 25 to 200 pitch range. Minimum bore sprockets are available in bore ranges from 1/4 to 8-3/8 in.
17 TOOTH #60 CHAIN IDLER SPROCKETS
8" X 1" X 1" 60G BENCH GRIND/WHEEL-PEABA810060 >
5" X 1/2" -DRIVE IMPACT SOCKET EXTENSIONS-ARS20923 >
United Abrasives SAIT 27050 11/16x1-1/4x1/4 Type A12 Vitrified Aluminum Oxide Mounted Points A60R, 10 pack
• Aluminum oxide grain
• Ideal for ID grinding and mold finishing
• Each point is dressed for perfect balance to perform without vibration or run-out
• Mandrel overhang "O" must always be the lowest possible. Maximum speeds given refer to overhang "O" equal to 1/2"
• Shank diameter 1/4”, length 1-1/2”
