V-BELTS COGGED AX-BX-CX-DX
NOTCHED GRIP V-BELTS-BRWCX136>
NOTCHED GRIP V-BELT-JASCX136>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >148-JASCX144 >
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 148-PIXCX144 >
NOTCHED GRIP V-BELT-JASCX150>
NOTCHED GRIP V-BELT-JASCX158>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 162-PIXCX158 >
NOTCHED GRIP V-BELT-JASCX173>
NOTCHED GRIP V-BELTS-BRWCX180>
NOTCHED GRIP V-BELTS-BRWCX240>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >72-JASCX68 >
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 79"-PIXCX75 >
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 85"-PIXCX81 >
NOTCHED GRIP V-BELTS-BRWCX85>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >90"-JASCX86 >
NOTCHED GRIP V-BELTS-JASCX90>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 94'-PIXCX90 >
NOTCHED GRIP V-BELT-JASCX96>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 100"-PIXCX96 >
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >183-JASBX180 >
JASON AX48 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 51" OUTSIDE LENGTH
COGGED RAW EDGE V-BELT. POLYESTER CORD REINFORCEMENT. RAW EDGE SIDEWALLS ELIMINATE SLIPPAGE AND INCREASES EFFICIENCY. COGGED DESIGN ALLOWS FOR GREATER HEAT DISSIPATION. THE BELT IS OIL AND HEAT RESISTAND AND CONFORMS TO ARPM STANDARD IP 20
'-JASAX48 >
JASON AX52 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 54" OUTSIDE LENGTH
AX SECTION COGGED CLASSICAL V-BELT. CONFORMS TO ARPM STANDARDS IP-20. THE COGGED RAW EDGE V-BELTS ARE DESIGNATED BY A LETTER INDICATING BELT SECTION, FOLLOWED BY "X" WHICH SIGNIFIES COGGED, RAW-EDGE CONSTRUCTION THAT HAS GREATER POWER CAPACITY THAN STANDARD WRAPPED CONSTRUCTION. INSIDE LENTH PLUS 2 " EQUALS OUTSIDE LENGTH
-JASAX52>
JASON AX53 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 55" OUTSIDE LENGTH
COGGED CLASSICAL V-BELT. 1/2 " TOP WIDTH. 5/16 " THICK. THIS IS A CLASSICAL SERIES BELT, WHICH IS MUCH HIGHER QUALITY AND STRONGER THAN An FHP BELT WITH THE SAME MEASUREMENTS.
-JASAX53 >
JASON AX55 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 57" OUTSIDE LENGTH
V-BELT, RUBBER, 1/2" X 57" OC. THE LOWER COMPRESSION SECTION OF THE BELT IS MADE OF HIGHLY FIBER REINFORCED, OIL AND HEAT RESISTANT.
-JASAX55 >
Recently Viewed
Magnolia Brush 99 Heavy Duty Handle Brace, Aluminum
TL-24-H-200-2012 Dodge® 113712 Dyna-Sync Type KF1 Timing Belt Pulley, 1/2 to 2 in Taper-Lock® Bore, 4.06 in OD, 24 Grooves, 3.82 in Dia Pitch, 2.34 in W Face
TL24H200-2012 Dodge® 113712 Dyna-Sync Type KF1 Timing Belt Pulley, 1/2 to 2 in Taper-Lock® Bore, 4.06 in OD, 24 Grooves, 3.82 in Dia Pitch, 2.34 in W Face
23-TOOTH #60-1 CHAIN SPROCKETS IDC 60-B-23-F1-7/16
23 TOOTH SPROCKETS FOR #60 CHAIN
Dichtomatik 75115266 O-Ring, 255 Dash Number, 5.609 in ID x 5.887 in OD, PTFE, 55 Durometer, Import
O-rings are endless, ring shaped sealing elements with a circular cross-section that are manufactured from elastomer materials or PTFE. The designation of an O-ring is derived from the dimensions of its inner diameter and cord width in millimeters, along with the name of the material and its Shore A hardness.
Browning® Gearbelt® 1055250 Type 2 Synchronous Timing Pulley With Flange, 5/8 to 1-5/8 in Bore, 3.79 in OD, 32 Grooves, 3.82 in Dia Pitch, 1 in W Face
Synchronous belt drives help reduce the problems of slippage, belt stretch, lubrication and metal to metal contact. They provide superior performance because power is transmitted by positive engagement of belt teeth rather than by friction, as in conventional belt drives.
Dichtomatik N70432 O-Ring, 432 Dash Number, 5.35 in ID x 5.9 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
