BEARING LOCK WASHERS
BEARING LOCKWASHER - WESW06 >
BEARING LOCKWASHER - WESW07 >
BEARING LOCKWASHER - WESW08 >
BEARING LOCKWASHER - WESW09 >
BEARING LOCKWASHER - WESW10 >
BEARING LOCKWASHER - WESW11 >
BEARING LOCKWASHER - WESW12 >
BEARING LOCKWASHER - WESW13 >
BEARING LOCKWASHER - WESW14 >
BEARING LOCKWASHER - WESW15 >
BEARING LOCKWASHER - WESW16 >
BEARING LOCKWASHER - WESW17>
BEARING LOCKWASHER - WESW18 >
This W19 lock washer is a high quality and durable inch lock washer that is manufactured to strict quality control standards. Lock washers are used to prevent the locknut from rotating by having an interior tab that locks into the shaft keyway and exterior tabs that lock the nut in position when one of the washer tabs is bent over into one of the slots around the circumference of the nut
BEARING LOCKWASHER - WESW20>
W-21 Lock Washer - 4.1920 in ID, 5.7030 in OD, 5.0000 in Face Dia., Steel Material
aterial
Steel
Number Of Tangs
19
Product Type
Bearing Lock Washers
BEARING LOCKWASHER
BEARING LOCKWASHER - WESW24 >
BEARING LOCKWASHER - WESW26>
BEARING LOCKWASHER - WESW28>
BEARING LOCKWASHER - WESW34>
BEARING LOCKWASHER - WESW36>
Recently Viewed
McGill® CAGEROL® machined race needle bearings are manufactured from bearing quality steel. Most sizes use crowned or end relieved, rollers to help reduce end stresses and allows for greater misalignment. The rollers are separated by a steel retainer (cage) to help achieve higher speeds and provide a lubricant reservoir. CAGEROL® bearings are constructed with radial lubrication hole and groove on the outer and optional inner raceway (MI series) for relubrication through the housing or shaft. Other options include a variety of seal configurations to either help prevent contaminant entry or contain the lubricant.
HEAVY DUTY LEFT HAND SCRAPERS FOR INTL HARVESTER-KABP195938>
FILTERS
Milwaukee® 2807-22 M18™ FUEL™ Hole Hawg™ Cordless Right Angle Drill Kit, 1/2 in Keyed Chuck, 18 V, 1550 rpm No-Load, 15.6 in OAL, Li-Ion Battery
Milwaukee®, WI - Milwaukee® tool continues to innovate in a category they invented 70 years ago by delivering ground-breaking performance with the introduction of the next generation of M18™ FUEL™ Hole Hawg™ with the power and speed to replace corded right angle drills. Designed from the ground-up with an upgraded POWERSTATE™ brushless motor and optimized REDLINK PLUS™ electronics and paired the REDLITHIUM™ HIGH OUTPUT™ 6 Ah batteries, the new M18™ FUEL™ Hole Hawg™® is the fastest in applications when drilling 7/8 in ship augers, delivering the ability to perform the fastest rough-ins in the industry. The tool is the lightest in class at around 7 lb. When paired with the kitted paired the REDLITHIUM™ HIGH OUTPUT™ 6 Ah batteries, the new M18™ FUEL™ Hole Hawg™ is able to drill up to 220 7/8 in holes with a ship auger on a single charge.
JASON 2-R-B-115 B SECTION NATURAL RUBBER BANDED V-BELTS, 21/32" TOP WIDTH, 13/32" THICK, 115" INSIDE LENGTH 2 RIBS
CONSISTENT PERFORMANCE IN MULTIPLE V-BELT DRIVES-ENSURE ALL BELTS WILL MEASURE WITHIN ARPM MATCHING STANDARDS. BANDED CONSTRUCTION-FABRIC/NEOPRENE TOP BAND ENHANCES STABILITY AND PREVENT BELTS FROM TURNING OVER OR COMING OFF THE DRIVE. OIL & HEAT RESISTANT
-JAS2RB115 >
Vortec Pro® 36024 Wide Face Wheel Brush With Nut, 6 in Dia Brush, 0.025 in Dia Standard/Twist Knot Filament/Wire, 5/8-11 Arbor Hole
