PEX Nipples
1 -MALE PIPE THREADX10 GALVANIZED NIPPLE
1 -MALE PIPE THREADX12 GALVANIZED NIPPLE
1 -MALE PIPE THREADX3 GALVANIZED NIPPLE
1 -MALE PIPE THREADX4 METAL GALVANIZED NIPPLE
1 -MALE PIPE THREADX5 METAL GALVANIZED NIPPLE
1 -MALE PIPE THREADX8 METAL GALVANIZED/ NIPPLE
1-1/2-MALE PIPE THREAD X 4-1/2 GALVANIZED NIPPLE - FIT11/2X41/2GN>
1-1/2" X 10" GALVANIZED NIPPLE-FIT11/2X10GN >
1-1/2" -MALE PIPE THREADX12" GALVANIZED NIPPLE
1-1/2" -MALE PIPE THREADX12" METAL GALVANIZED NIPPLE-FIT11/2X12GN >
1-1/2" -MALE PIPE THREADX2-1/2" GALVANIZED NIPPLE-FIT11/2X21/2GN >
1-1/2" -MALE PIPE THREADX2" METAL GALVANIZED NIPPLE-FIT11/2X2GN >
1-1/2" -MALE PIPE THREADX3-1/2" GALVANIZED NIPPLE-FIT11/2X31/2GN >
1-1/2" -MALE PIPE THREADX3" GALVANIZED NIPPLE-FIT11/2X3GN >
1-1/2" -MALE PIPE THREADX4" GALVANIZED NIPPLE-FIT11/2X4GN >
1-1/2" -MALE PIPE THREADX5-1/2" GALVANIZED NIPPLE-FIT11/2X51/2GN >
1-1/2" -MALE PIPE THREADX5" GALVANIZED NIPPLE-FIT11/2X5GN >
1-1/2" -MALE PIPE THREADX6" GALVANIZED NIPPLE-FIT11/2X6GN >
1-1/2" -MALE PIPE THREADX7" GALVANIZED NIPPLE-FIT11/2X7GN >
1-1/2" -MALE PIPE THREADX8" GALVANIZED NIPPLE-FIT11/2X8GN >
1-1/2" -MALE PIPE THREADXCLOSE GALVANIZED NIPPLE-FIT11/2XCLGN >
1-1/2" X CLOSE GALVANIZED NIPPLE-JPW11/2XCLGN >
1-1/4" -MALE PIPE THREADX10" GALVANIZED NIPPLE-FIT11/4X10GN >
1-1/4" -MALE PIPE THREADX12" GALVANIZED NIPPLE-FIT11/4X12GN >
Recently Viewed
SENTRY GREEN SAFETY HELMET HARDHAT-AMS14045 >
Browning 14-TOOTH #40-1 CHAIN SPROCKETS BRW H-4014 X 1-1/8
Browning® finished bore sprockets are offered in single strands. Offerings include 35 to 100 pitch range. Finished bore sprockets are available from 3/8 to 2-7/16 in. Hardened teeth are available up to 30 teeth.
MORSE® 11378 1330 General Purpose Jobber Length Drill Bit, 3/64 in Drill - Fraction, 0.0469 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MORSE® 11378 1330 General Purpose Jobber Length Drill Bit, 3/64 in Drill - Fraction, 0.0469 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MORSE® 16771 1391 Aircraft Extension Drill, #42 Drill - Wire, 0.0935 in Drill - Decimal Inch, 135 deg Point, HSS
MORSE® 16771 1391 Aircraft Extension Drill, #42 Drill - Wire, 0.0935 in Drill - Decimal Inch, 135 deg Point, HSS
IKO LRB121612 Inch Series Inner Ring With Oil Groove, 3/4 in ID x 1 in OD, 19.3 mm OAW, For Use With BR162412 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
MARXMANâ„¢ 85068 330QI General Purpose Jobber Length Drill Bit, #14 Drill - Wire, 0.182 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MARXMANâ„¢ 85068 330QI General Purpose Jobber Length Drill Bit, #14 Drill - Wire, 0.182 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
