HCI PREFERRED SUPPLIER
8" X 800' ROLL HAND TOWEL--ROLL-SCO01040 >
7-pound white, Portland cement-based powder waterproofer used to seal, protect, and decorate vertical masonry surfaces.
8" X 425' ROLL HAND TOWEL--CS/12-SCO01080CASE >
6" X 6" HINGED FOAM TRAYS--CS/500-WHY0109BW >
01179-WP CLIPS FOR 12" BELTING UNIBAR U4C12 UX-1-S-12 UNIBAR FASTENERS
FASTENERS-COV01179WP >
7/8" X 3-3/4" CLEVIS PIN HOLE WRONG-HIG01200>
a 21-pound pail of white, Portland cement-based powder waterproofer used for sealing, protecting, and decorating masonry, concrete, and brick surfaces.
FASTENERS-COV01251WP >
Thread Diameter: 3/4 in Take-Up/Travel: 6 in Working Load Limit (WLL): 5,200 lb (5:1 design factor) Closed Length: 14-3/4 into 17 in Material & Finish: Drop-forged steel, hot-dip galvanized
12" UCM-36" STAINLESS STEEL BELT LACING-COV01309 >
14-OZ MULTI-PURPOSE #2 LITHIUM GREASE-SPL01400 >
36" X 84 DOOR WEATHERSTRIP KIT-M-D01438 >
14-OZ HI-TEMP #2 LITHIUM GREASE-SPL01500 >
3/8" X 3-1/2" HITCH PIN-HIG01518 >
TRAILER JACK 2"-OD BUSHINGS-HBC015273>
RATCHET JACK 1"-PIN 1-1/4"-THREAD - HIG01542>
TRAILER JACK MOUNTING PLATE-HBC015909 >
FAN SWITCHES-FAN01722>
SWITCH FOR MODEL AMB-3221 - FAN01723 >
TRAILER JACK DISC FOOT-HBC018173 >
Type: Round Bend U-Bolt with two hex nuts Material: Low carbon steel Finish: Zinc-plated (Part #50080-7) or Hot Galvanized (Part #53080-4) Thread Size: 3/8"-16 UNC Inside Width: 1-1/2 in Inside Length: 2-1/2 in Thread Length: 1-1/4 in Pipe Size: 1 in
SIZE 6/7 SMALL SHOE COVER-WIK02 >
3/16" -1/4" FUEL LINE HOSE CLAMPS-MED02040 >
CABLE SWIVEL STOPS-MED02099 >
Recently Viewed
1/4" -HOSEX6-FEMALE JIC 90 HYDRAULIC HOSE END-MHDE0406FJ90 >
2" FINE GRIT. SURFACE PREP PAD, QUICK CHANGE. REPLACEMENT SURFACE PREP PAD FITS FORNEY 60270 OR 71914" BACKING PAD - Used to prepare surface before priming and painting. Primarily used for detailed or hard to reach areas with a quick release roll lock feature for easy accessibility.
Mayhewâ„¢ 62065 X-Long Pin Punch Kit, 5 Pieces
30-AMP 600-VOLT AC FA FUSES-EDIMCL30 >
The Starrett 196 Universal Back Plunger Dial Indicator features graduations to .001" and 0.02mm that handle by far the majority of jobs. Shank diameter is 1/4" (6.3mm). Antimagnetic models are also available - (inch reading) 196A6Z and 196B6. For full use, the operator first chooses the proper contact from the three hardened contact points that come with each model. Then the contact should be brought against the work with enough pressure to give the hand one full turn. Set the hand at zero by rotating the dial with the knurled bezel. This provides one full rotation of the hand both to the right and left of zero, showing a rise or drop in the work and the amount of that variation. 0-100 with 3 Contact Points, Adapter, 4 Attachments in Case This provides one full rotation of the hand both to the right and left of zero, showing a rise or drop in the work and the amount of that variation.
600-LB CAPACITY WITH 10" PUNCTURE PROOF TIRES HAND TRUCK - GLE40107>
