HCI PREFERRED SUPPLIER
11/2 1-1/2" X 1/2" X 1-1/2" Black Tee
1-1/2" X 1/2" X 1-1/2" BLACK TEES-JPW11/2X1/2X11/2BT>
11/2X11/2-ANGLE 1-1/2x1-1/2x1/4" Long Angle
1-1/2X1-1/2X1/4" LONG ANGLE STOCK-JMS11/2X11/2ANGLE >
11/2X11/2X1-BT 1-1/2" X 1-1/2" X 1" Black
1-1/2" X 1-1/2" X 1" BLACK TEE-FIT11/2X11/2X1BT >
11/2X11/2X1-BT 1-1/2" X 1-1/2" X 1" Black Tee
1-1/2" X 1-1/2" X 1" BLACK TEE-JPW11/2X11/2X1BT >
11/2X11/2X1/2BT 1-1/2" X 1-1/2" X 1/2" Black
1-1/2" X 1-1/2" X 1/2" BLACK TEE-JPW11/2X11/2X1/2BT >
11/2X11/2X3/4BT 1-1/2" X 1-1/2" X 3/4" Black
1-1/2" X 1-1/2" X 3/4" BLACK TEE-FIT11/2X11/2X3/4BT >
11/2X11/2X3/4BT 1-1/2" X 1-1/2" X 3/4" Black Tee
1-1/2" X 1-1/2" X 3/4" BLACK TEE-JPW11/2X11/2X3/4BT >
11/2X11/2X3/4GT 1-1/2" X 1-1/2" X 3/4" Galvanized
1-1/2" X 1-1/2" X 3/4" GALVANIZED TEE-FIT11/2X11/2X3/4GT >
11/2X11/4BB3000 1-1/2" X 1-1/4" Black Bushing 3000#
1-1/2" X 1-1/4" BLACK BUSHING 3000#-FIT11/2X11/4BB3000 >
11/2X11/4BR3000 1-1/2" X 1-1/4" Reducer
1-1/2" X 1-1/4" REDUCER 3000-LB-FIT11/2X11/4BR3000 >
11/2X6-SSN-316 1-1/2" -male Pipe Threadx6" 316" Stainless Steel
1-1/2" -MALE PIPE THREADX6" 316" STAINLESS STEEL NIPPLE-FIT11/2X6SSN316 >
11/32" EXTERNAL RETAINING RINGS ANR 1400-34
CONSTRUCTED AS CURVED BEAMS OF UNIFORM STRENGTH, THE RADIAL WIDTH IS REDUCED TOWARDS THE FREE ENDS SO THAT A CONSTANTLY ROUND SHAP IS MAINTAINED THROUGHOUT CONTINUOUS USE. THIS FORM OF CIRCLIP OFTEN USED IN ASSEMBLIES SUBJECTED TO STRONG CENTRIFUGAL FORCES, IS ALSO SECURE AGAINST HIGH ROTATIONAL SPEEDS. LUGS WITH HOLES ARE PROVIDED FOR RAPID FITTING OR REMOVAL WITH CIRCLIP PLIERS.
11/4X 1-BR-3000 HCI PREFERRED SUPPLIER
1-1/4" X 1" BLACK REDUCER 3000#-FIT11/4X1BR3000 >
11/4X11/4X1/2BT 1-1/4" X 1-1/4" X 1/2" Black
1-1/4" X 1-1/4" X 1/2" BLACK TEE-FIT11/4X11/4X1/2BT >
11/4X11/4X1/2BT 1-1/4" X 1-1/4" X 1/2" Black Tee
1-1/4" X 1-1/4" X 1/2" BLACK TEE-JPW11/4X11/4X1/2BT >
11/4X11/4X1/2GT 1-1/4" X 1-1/4" X 1/2" Galvanized
1-1/4" X 1-1/4" X 1/2" GALVANIZED TEE-FIT11/4X11/4X1/2GT >
11/4X11/4X3/4BT 1-1/4" X 1-1/4" X 3/4" Black
1-1/4" X 1-1/4" X 3/4" BLACK TEE-FIT11/4X11/4X3/4BT >
11/4X11/4X3/4BT 1-1/4" X 1-1/4" X 3/4" Black Tee
1-1/4" X 1-1/4" X 3/4" BLACK TEE-JPW11/4X11/4X3/4BT >
11/4X11/4X3/4GT 1-1/4" X 1-1/4" X 3/4" Galvanized
1-1/4" X 1-1/4" X 3/4" GALVANIZED TEE-FIT11/4X11/4X3/4GT >
11/64" E-CLIP RETAINING RINGS ANR 1500-17
THE BASIC E-CLIP PROVIDES RELATIVELY LARGE SHOULDER HEIGHT FOR A SMALL SHAFT DIAMETER. ONLY GROOVE SIZE IS CRITICAL WITH THIS TYPE OF CIRCLIP, THE SHAFT DIAMETER CAN BE VARIED WIDELY
-ANR150017 >
110-075 3/4" X 30-yards Green Finger
3/4" X 30-YARDS GREEN FINGER TAPE-MOD110075 >
Recently Viewed
OIL SEALS-NAT5121>
OIL SEALS-NAT5123>
SEAL KITS-NAT5603>
OIL SEALS-NAT55187>
1/10-AMP 600-VOLT AC FA FUSES-LITKLK1/10 >
